Skip to content

Common problems

The receiver

The receiver does not appear in the list
  • Check that it is on and close to the phone, and that the phone's Bluetooth is on.
  • Tap Search again: the search lasts a short time.
  • If geosit says Bluetooth permission needed, grant the permission again from the phone settings (Apps → geosit → Permissions).
  • A receiver connected to another phone cannot be seen: disconnect it from the other one.
  • On iPhone the receivers with the first firmware (classic Bluetooth only) cannot be seen: see geosit on iPhone.
«Pairing failed»

Turn the receiver off and on again and try again. If the phone had already paired it in the past, press and hold the receiver in the list to forget it and connect it again from scratch.

«This instrument is not in the license»

The license is valid only for certain receivers, or for the first ones that connected and the places are used up. Ask the reseller to unbind the old receiver or to add a place; then Settings → License → Update.

The Home screen says «Reconnecting…»

The receiver has turned off, has moved away or has not sent data for more than ten seconds. geosit retries on its own: move closer, check the receiver's battery. To stop retrying, Receiver → Disconnect.

Just connected, the receiver gives no position

It happens if the receiver was still starting up. geosit sends it the output commands again by itself after 5, 10 and 20 seconds, so the raw data is recorded too. If after half a minute the position still does not arrive, switch the receiver off and on and connect it again.

Accuracy

The FIX does not arrive
  1. Are the corrections arriving? Open the status panel: the Age of corrections must stay below a few seconds. If it is not there, check the Status in Settings → NTRIP corrections.
  2. Is the sky too closed? Look at the signal chart in the receiver status: under thick canopy, move towards a clearing or raise the pole.
  3. Wait: from FLOAT to FIX it can take from a few seconds to a few minutes.
  4. Where the FIX just does not arrive, use static or Stop & Go and post-process in the office.
The corrections say «Refused»

The caster refused the user, password or mountpoint. Open the caster card and check the fields; for the mountpoint tap it and choose from the caster's list.

The corrections say «Error»

The mobile data network is missing, or the caster does not respond. geosit retries on its own; check that the phone can browse the Internet.

The elevations are wrong by 40-50 metres

It is the difference between ellipsoidal heights and elevations above sea level. Press and hold the project → Elevations and choose the right one: the change also applies to the points already measured. See Projects.

The elevations are wrong by about two metres

Probably the pole height is not the real one. It must be set before measuring: the points already measured carry the pole with which they were taken.

The measurement

There is no Measure button

Without a receiver connected geosit never shows the measure button: connect the receiver, or choose the demo receiver to try it out. If the receiver is connected, check that you are not holding a distance or area tool (Close).

«Measurement cancelled»

During the measurement the screen was left (another app, a call, the home button): the point was not saved. Repeat the measurement staying in the survey.

«Point not saved»

During the measurement no valid position arrived from the receiver. Check the connection and the solution, then measure again.

The survey does not open and «License required» appears

The trial has ended or the license has expired: enter the code in Settings → License. The data all remain and can be exported.

Stakeout

The arrow points in a wrong direction

The arrow uses the phone's compass, which suffers from nearby metal. Hold the phone flat, away from cars and tools, and recalibrate the compass by drawing a figure eight in the air. In any case the distance and the ↑ → offsets in metres are what count.

There is no «Stake out» in the point card

It appears only with the receiver connected.

Import, export and maps

«No points found» when importing a CSV

The file must have one row per point: name, easting, northing, elevation (or name, latitude, longitude, elevation). Check the separator and that the coordinates are numbers. See Importing points from a CSV.

The imported points end up very far away

The project's reference system is not that of the file's coordinates. Delete the imported points, give the project the file's system (press and hold the project → Reference system) and import again.

The map is grey or checkered

Streets, satellite and WMS need the network: without network you only see the areas already loaded. In the woods use an offline map. A slow WMS service can show empty squares for a few seconds.

The photo cannot be taken

If geosit says No camera, the phone is missing a camera app. Alternatively use Gallery with a photo already taken.

Contacts

For everything else write to developer@solutop.eu (also from Settings → About → Write to us), stating the phone model, the geosit version and what you were doing.